Contact

National

Stingl GmbH
Dimbacher Straße 25
74182 Obersulm-Willsbach

07134 / 13797-11

International

Stingl Systems GmbH
Dimbacher Strasse 25
D-74182 Obersulm-Willsbach

+49 7134 13797-11

News

09.04.2019
Review: The 36th Heilbronn Lift Days 2019

Also in 2019, Stingl GmbH took part as exhibitor at the Heilbronn lift days. A home game for STINGL ...

by Stingl GmbH

Product catalog

Stingl-mobil PANO

Stingl-mobil PANO

Telescopic work scaffolding made of glass reinforced polyester (GRP), which can be used in various shafts.

Stingl-mobil PANO can be installed at any shaft door opening independent of the number of landings. The areas of application range from panoramic lifts to all those lifts where the shaft walls cannot be used as fixing ground for platforms. Stingl-mobil PANO is the perfect tool for installation of machine roomless lifts with machinery located in the shaft head as well as for service and repair work on existing units.

Telescopic working platform made of glass reinforced polyester (GRP)

Unlike conventional, static working platforms, Stingl - mobil PANO is designed for multiple use in shafts with depths ranging from 1000mm to 2000mm (in 250mm steps). The scaffolding is designed for a working load of max. 3 kN/m² per level. It does not require a substructure. The following scaffolding widths (working area) are available: 700 mm and 1000 mm. Due to the favourable properties of GRP as well as an intelligent lightweight construction, installation can be performed by one trained person (e.g. elevator fitter).

Variant 1

Stingl-mobil PANO - Working platform flush with floor level
Stingl-mobil PANO - Working platform flush with floor level

Scaffolding made of GRP with one working level incl. lateral fall protection devices according to DIN EN 12811-1. The perfect configuration for modernisation and maintenance work like drive change, rope change, rescue or loosening brakes.

Variant 2

Stingl-mobil PANO - Working platform about 1.25 m above floor level
Stingl-mobil PANO - Working platform about 1.25 m above floor level

Scaffolding made of GRP with one working levels incl. lateral fall protection devices according to DIN EN 12811-1. The working level is reached by means of an access ladder. This variant allows safe working for example in 2,70m to 3,20m high shaft heads of machine roomless lifts.

Variant 3

Stingl-mobil PANO - Upper working platform about 1,92 m above floor level
Stingl-mobil PANO - Upper working platform about 1,92 m above floor level

Scaffolding made of GRP with two elevated working level incl. lateral fall protection devices according to DIN EN 12811-1. The upper scaffolding level can be accessed over a rung ladder.. This variant allows safe working for example in 3,40m to 3,90m high shaft heads of machine roomless lifts.

Benefits:

  • A GS-seal (certificate no. 02121) awarded by the German employers' liability insurance association guarantees a safe and approved solution.
  • The platform can be used in shafts without rear wall (e.g. panoramic lifts, open through-lifts).
  • The requirement of one-man-assembly is met by the moderate weight of the scaffold elements (the heaviest subassembly weighs approx. 31 kg).
  • No dependence on third parties for scaffolding erection and thus administrative savings.
  • Considerable savings compared with conventional wooden scaffolds as the mobile scaffold can be used again.
  • Since no substructures are required, the mobile scaffold can be installed quickly; it is also flexible in use and thus highly economical.
  • The modular design allows the assembly of a single or bi-level mobile scaffolding.
  • Defined material properties of GRP, such as high loading capacity, high impact strength, long service life, low weight, high corrosion resistance as well as electrical insulation are the advantages of GRP over conventional materials such as wood, steel or aluminium.
  • Low installation time of approx. 50 minutes by trained personnel.
Requirements
Stingl-mobil PANO
Stingl-mobil PANO

Installation requirements Stingl-mobil PANO

  • Save working load 300 kg/m²
  • Stingl-mobil PANO may only be mounted on sufficiently stable parts of structural works capable of taking up and passing on the forces which are produced
  • The lintel section must be able to withstand horizontal forces of min. 3,5 kN
  • The door threshold must be able to withstand horizontal forces of min. 4,2 kN and vertical forces of min 6,6 kN
  • Base plates or screw jacks with base plates must be in firm contact with both the sills and the legs of the scaffolding. Compensate for uneven ground with screw jacks with base plates. NEVER USE unstable objects such as blocks, loose bricks, etc.
  • The vertical wall with the door opening for mounting must be concrete (wall thickness min. 100 mm)
  • The front vertical girder must extend higher than the door opening by at least 100 mm. The distance between floor and ceiling must not be shorter than 2.350 mm
Stingl-mobil PANO
Stingl-mobil PANO
  • Before setting foot on the upper work platform, at least two telescopic spacers must be mounted as per the installation instructions and extended out to the surrounding shaft wall, profiled girder or guide rails. If the spacers are placed between the working platform and existing elevator guide rails, this must be done with adapters, which can be supplied additionally
  • It must be ensured that the spacers (telescopic rods) can be placed perpendicular to the working platform and push against the shaft wall. The gap between the perimeter of the working platform and the shaft wall may not exceed 1.000 mm.
  • The following maximum shaft widths must be observed when using the platform:
    Platform width of 700 mm: maximum shaft width 2.800 mm
    Platform width of 1.000 mm: maximum shaft width 3.100 mm
    Required minimum opening widths to ensure proper installation: platform width plus 100 mm
  • Guardrails must be used on all open sides and ends of scaffold platforms. Top, midrails and toeboards are required
  • All socket pins must be secured with split pins at any time
  • A detailed drawing and specifications must be kept with the scaffold on the job
  • Safety gear for fitters like for example fall arrester, full body harness, suitable anchorage point etc. must be used in accordance with local requirements at all times during the erection, use and dismantling of the platform
  • Be careful while handling inner and outer GRP tubes as well as guard rail sections with inner and outer parts. Interior parts might slide out easily causing damage or injuries.
Product overview

Variant 1 - single level platform

Item No. Description (platform width / platform depth)
16001061001 Stingl-mobil PANO 600 / 1.000, without fall protection
16001062001 Stingl-mobil PANO 600 / 1.000 - 2.000
16001062002 Stingl-mobil PANO 600 / 1.000 - 2.000, without fall protection
16001072003 Stingl-mobil PANO 700 / 1.000 - 2.000
16001072005 Stingl-mobil PANO 700 / 1.000 - 2.000, without fall protection
16001102001 Stingl-mobil PANO 1.000 / 1.000 - 2.000
16001102003 Stingl-mobil PANO 1.000/1.000-2.000, without fall protection
Accessories for Variant 1 - single level platform
Item No. Description
01602072001 GRP panel kit 600 mm 1.000 - 2.000 mm, 8-part
16005072001 GRP panel kit 700 mm 1.000 - 2.000 mm, 8-part
16005102001 GRP panel kit 1.000 mm 1.000 - 2.000 mm, 8-part
16007062001 Stingl-mobil PANO 600 / 1.000 - 2.000 upper platform
16007072001 Stingl-mobil PANO 700 / 1.000 - 2.000 upper platform
16007072002 Stingl-mobil PANO 700 / 1.000 - 2.000 upper platform without fall protection
16007102001 Stingl-mobil PANO 1.000 / 1.000 - 2.000 upper platform
16007102002 Stingl-mobil PANO 1.000 / 1.000 - 2.000 upper platform without fall protection
16015060001 Stingl-mobil PANO fall protection 600
16015070001 Stingl-mobil PANO fall protection 700
16015100001 Stingl-mobil PANO fall protection 1.000

Variant 2 - elevated platform

Item No. Description (platform width / platform depth)
16001072001 Stingl-mobil PANO 730 / 1.000 - 2.000
16001072002 Stingl-mobil PANO 730 / 1.000 - 2.000, without fall protection
16001082001 Stingl-mobil PANO 830 / 1.000 - 2.000
16001082002 Stingl-mobil PANO 830
/ 1.000 - 2.000, without fall protection
16001112001 Stingl-mobil PANO 1.130 / 1.000 - 2.000
16001112002 Stingl-mobil PANO 1.130 / 1.000 - 2.000, without fall protection
Accessories for Variant 2 - elevated platform
Item No. Description
16007072003 Stingl-mobil PANO 730 / 1.000 - 2.000 upper platform
16007082001 Stingl-mobil PANO 830 / 1.000 - 2.000 upper platform
16007082002 Stingl-mobil PANO 830 / 1.000 - 2.000 upper platform, without fall protection
16007112001 Stingl-mobil PANO 1.130 / 1.000 - 2.000 upper platform

Variant 3 - double level platform

Item No. Description (platform width / platform depth)
16002062001 Stingl-mobil PANO 600 / 1.000 - 2.000
16002072001 Stingl-mobil PANO 700 / 1.000 - 2.000
16002072003 Stingl-mobil PANO 700 / 1.000 - 2.000, without fall protection
16002102001 Stingl-mobil PANO 1.000 / 1.000 - 2.000
16002102003 Stingl-mobil PANO 1.000
/ 1.000 - 2.000, without fall protection
Accessories for Variant 3 - double level platform
Art.-Nr. Bezeichnung
16005062002 GRP panel kit 600 mm for double level platform 1.000-2.000 mm
16005072002 GRP panel kit 700 mm for double level platform 1.000-2.000 mm
16005102002 GRP panel kit 1.000 mm for double level platform 1.000-2.000 mm
Accessories for all variants
Item No. Description
01311000002 Full body harness
013999003 Fall arrester
16015000001 Stingl-mobil PANO lateral fall protection for the door area
16022049801 Threshold shoe, 498 mm long
16022072801 Threshold shoe, 728 mm long
16027070001 Stowage box kit for Stingl-mobil PANO (2 boxes)
01609070001 Stowage box kit for Stingl-mobil PANO (3 boxes)
08004102001 Stowage box type 4
08004263001 Stowage box type 5

Video

 

 

Patent-Nr. PCT 202700;
229243; US 7,108,100

Copyright © 2019 Stingl GmbH
This website uses cookies to provide the best possible functionality.
By using this offer, you agree that we may leave cookies on your computer. More information...
OK